CISCO ONS 15216-EDFA2-A Metro Erbium Dopped Fiber Amplifier 17dBm with SNMP, Rev 2

BRAND NEW SYSTEM - STILL SEALED IN FACTORY PACKAGING. 1x ONS 15216 Metro EDFA2-A. 1x 19 rackmount kit (installed). 1x 24 (telco) rackmount kit. 1x set of manuals and documentation.

The item you will be receiving is factory sealed in original packaging. We have opened one in order to get good photographs, however buyers will be receiving a brand new one, sealed in the box.

1530 nm to 1563 nm. 27 dBm to 4 dBm (total all channels).

Unidirectional (two common fibers: one transmit, one receive). 17 ± 0.6 dBm. 13 dB to 22 dB. Channel gain deviation from setpoint.

The ONS 15216 EDFA2 contains an active gain block with an automatic gain control loop to minimize the effects of output power variations per wavelength upon adding or deleting wavelengths on the same DWDM ring. ONS 15216 EDFA2 Mechanical Specifications. Dimensions (H x W x D).

(4.4 cm x 43.7 cm x 27.9 cm). 5.45 lb (2.47 kg). 32 to 122°F (0 to 50°C). 40 to 185°F (-40 to 85°C). Relative humidities of 5 to 95%, non-condensing.

With ambient temperatures above 84° F (29°C), the relative humidity may be limited to that corresponding to a specific humidity of 0.024 pounds of water per pound of dry air. Mean time between failures (MTBF). 12.7 years as per calculation procedure outlin. The ONS 15216 EDFA2 has the following external features.

Front panel LEDs, graphics, and warning displays. Brackets for rack mounting (including reversible ears that permit front, mid, and rear mounting).

Rear and side cooling vents. Access door for fiber cleaning. Fiber routing and retaining feature. Two threaded grounding holes on the ONS 15216 EDFA2-A (studs on the ONS 15216 EDFA2) on rear, and two threaded grounding holes on each side. Screw lug terminal block for power connection.

RJ-45 connector for external alarm connection. RJ-45 connector for LAN connection. SC/UPC connectors for optical interface.

DB-9 female connector for craft EIA/TIA-232 serial interface connection. ONS 15216 EDFA2 Front Panel Features. Terminal strip for supplying power to the ONS 15216 EDFA2. Attach AWG 18 stranded power wires to appropriate terminals. Threaded grounding holes (#10-32) to ground the ONS 15216 EDFA2.

RJ-45 connector used for alarm system connection. See the "Alarm Out Relay Interface (RJ-45)" section. Serial port for local or remote (modem) data communication connection. Laser warnings, designation labels, and power level warning. LEDs indicating status of power, fail, loss of signal, Ethernet link availability and Ethernet link traffic. See the "Alarm LEDs" section. SC/UPC port for fiber that taps off 1% of output signal for monitoring purposes. Rear panel chassis ground to attach ground lug or wires using #10-32 screws to the ONS 15216 EDFA2-A (#8-32 nut to the ONS 15216 EDFA2). RJ-45 connector used for 10BASE-T Ethernet connection. The ONS 15216 EDFA2 is a technology for bandwidth-on-demand wavelength services. Depending on the settings and the input power, every wavelength in a ONS 15216 EDFA2 is guaranteed to be amplified by 13 to 22 dB. With the ONS 15216 EDFA2's gain control technology, amplification for each wavelength remains constant at all times as wavelengths are added or dropped from an optical fiber. As long as the total (composite) input power of all wavelengths is between 4 dBm and -27 dBm, any number of wavelengths can be amplified. The ONS 15216 EDFA2 uses wavelength protection switching to restore wavelengths that are lost in the event of a fiber cut or other loss of signal. In this example, two wavelengths are routed clockwise around a metro ring, and two wavelengths are routed counter-clockwise around the same ring. Of the two counter-clockwise wavelengths, only one transits the span linking locations D and C.

If a fiber cut occurred on this span, the affected wavelength could be restored by rerouting it (clockwise) around the ring to location D. Wavelength protection switching minimizes the amount of bandwidth allocated for restoration because only the affected wavelength is restored, not the entire fiber.

The ONS 15216 EDFA2 has the following key features. Adjustable constant gain of 13 to 22 dB. Simple Network Management Protocol (SNMP) MIBs.

Constant amplification (gain) per wavelength is important for ensuring that variations in power between channels at the receivers is minimized. As wavelengths are added/dropped from an optical fiber, small variations in gain between channels in a span can cause large variations in the power difference between channels at the receivers.

The ONS 15216 EDFA2 enables bandwidth-on-demand services by guaranteeing that every wavelength is amplified by a value that can be set between 13 and 22 dB, no matter how many wavelengths are being amplified. Constant gain is achieved using an automatic control circuit that adjusts pump power when changes in input power are detected. The ONS 15216 EDFA2 operates in Constant Gain Temperature Compensated mode by default, but since there may be applications where other operating modes may be required, the ONS 15216 EDFA2 can be set to operate in any one the following pump control modes.

Constant Gain Temperature Compensated mode. Fiber (a) in the figure shows a set of channels with equal powers being input to a cascaded network of amplifiers that produce vastly different power levels and optical signal-to-noise ratios (OSNR) at the output.

In contrast, fiber (b) shows how the EDFAs effectively reduce this effect by introducing a gain flattening filter within each amplifier. Transients in the performance of optical amplifiers are inevitable whenever the number of signals, or the relative power of signals, changes. The ONS 15216 EDFA2 uses transient suppression to reduce the amount of time required by an amplifier to recover from a change.

This indicates the suitability of the amplifier for add/drop applications like those described earlier. Whenever there is gain in an optical system, noise also occurs.

The predominant source of noise in EDFAs is amplified spontaneous emission (ASE). The ONS 15216 EDFA2 has a low noise figure. If automatic laser shutdown is enabled, when the input power (signal) goes below the loss of signal value, the laser pumps are shut down until the input signal is restored.

This option prevents ASE (typically -3.5 dBm) from being present at the output during the loss of signal. The ONS 15216 EDFA2 SNMP MIBs contain definitions of management information that allows network systems to be remotely monitored, configured, and controlled. The ONS 15216 EDFA2 has a TL1 interface available to the network operator and craftsperson. Please feel free to ask any question! Our store accredited facility, or other mutually approved intermediary to inspect the system prior to final export. CALL: +1.303.931.8823 WITH ANY QUESTIONS. The item "CISCO ONS 15216-EDFA2-A Metro Erbium Dopped Fiber Amplifier 17dBm with SNMP, Rev 2" is in sale since Tuesday, October 8, 2019.

This item is in the category "Business & Industrial\Test, Measurement & Inspection\Test Equipment Parts & Accessories\Other Test Equipment Parts & Accessories". The seller is "hyp3" and is located in Boulder, Colorado. This item can be shipped to United States, United Kingdom, Mexico, Germany, Japan, Brazil, France, Australia, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Austria, Bahamas, Israel, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica, Bangladesh, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Liechtenstein, Luxembourg, Monaco, Macao, Martinique, Nicaragua, Peru, Pakistan, Paraguay, Viet nam, Uruguay, Canada.

Brand: CISCO
Model: ONS 15216-EDFA2-A
Type: DWDM, WDM, 10 GIG-E
MPN: ONS 15216-EDFA2-A